Owner’sManualModel No. 139.53664SRT2For Residential Use OnlyCaution:Read and follow all safety rules and operating instructions before first use of th
Assembly Step 4Install the Belt & Set the Belt Tension1. Drop the notched side of the trolley clip into the retaining slot on top of the trolley.
You have now finished assembling your garage door opener. Please read the following warnings before proceeding to the installation section
Installation Section: Pages 12-27Installation Step 1Determine Header Bracket LocationInstallation procedures vary according to garage door types. Foll
ONE*PlEC£ Door Without TrackRead the Safety instructions on page 12. They also apply to doors without tracks.' Close the door and mark the inside
Installation Step 2Install the Header BracketYou can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the
Installation Step 3Attach the T-rail to the Header BracketHeader Wall• Position the opener on the garage floor below the header bracket. Use packing m
Installation Step 4Position the OpenerFollow instructions which apply to your doortype as illustrated.A CAUT10WTo prevent damage to steel, alumin
Installation Step 5Hang the OpenerThe opener could fall and injure someone if it is not properly secured. Fasten the opener securely to
Installation Step 6Install the Premium Control ConsoleLocate the door control within sight of the door at a minimum height of 5 feet where small child
6. Attach the User Safety Instruction label to the wall near the door control, and the Maintenance Instruction label in a prominent location on the in
Contents PageA review of safety alert symbols...2You'll need tools...
Installation Step 9Electrica! RequirementsTo reduce the risk of electric shock, your garage door opener has a grounding type plug with a third groundi
The Safety Reversing Systeminformation you'll need before you begin the installation of the safety reversing sensor.The safety reversing sensor m
Installation Step 10Install the Safety Reversing SensorFigures 2 and 3 show assembly of brackets and "C" wrap based on the recommended insta
• Center each sensor unit in a “C“ wrap with lenses pointing toward each other across the door (see Figure 6).• Secure sensors with the hardware
Installation Step 11Fasten Door BracketFollow instructions which appiy to your door type as illustrated below or on page 25.^CAUTIONTo prevent
Alt ONE'^PIECE Door Nistatla^on ProcedurePlease read and comply with the warnings and reinforcement instructions on page 24. They apply to one-pi
Installation Step 12Connect Door Arm to Trolley Follow instructions which appiy to your door type as iilustrated below and on page 27.SeCTIQNAi OnlyMa
Alt 0№PIEC£ DoorsAssemble the Door Arm:• Fasten the straight and curved door arm sections together to the longest possible length, with a 2 or 3 hole
Adjustment Section: Pages 28 - 30Adjustment Step 1Adjust the UP and DOWN Limits Do not make any limit adjustments until the safety reversing sensors a
Adjustment Step 2Adjust the ForceForce adjustment controls are located on the right side panel of the opener. Force adjustment settings regulate the a
You'll Need ToolsDuring assembly, installation and adjustment of the opener, instructions will call for hand tools shown below.An unbalanced ga
Adjustment Step 3Test The Safety Reversing Sensor• Press the remote control push button to open the door.• Place the opener carton in the path of the
IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of severe injury or death to persons:1. READ AND FOLLOW ALL INSTRUCTIONS.2. Do not permit children eit
Operation of Your OpenerActivate the opener with any of the foliowing:• The Remote Control: Hold push button down until the door starts to move.• Th
Receiver and Remote Control ProgrammingYour garage door opener receiver and remote control have been pre-set at the factory. The door will open when y
Having a Problem?SituationProbable Cause and SolutionThe opener doesn't operate from either the Door Control or the remote contmi:1. Does
Having a Problem? (continued)SituationProbable Cause & SolutionThe door opens but won't close:1. If the opener lights blink, check the safet
Repair PartsRail Assembly PartsKEYNO.PARTNO.DESCRIPTION1 1A995Master link kit241B3869Complete trolley assembly3 1B3117 T-rail - center section4183B110
Repair PartsOpener Assembly Parts8-^KEY PART NO. NO.DESCRIPTIONKEY PART NO. NO.DESCRIPTION7841A437141A4885-341A281741B4245 41C4876 41A5021-2C41A4924
AccessoriesSears offers many useful accessories for your garage door opener. They are illustrated below with Sears model numbers and des
IndexAccess Door/Outside Key Release Accessory...
âECÎlONAt Door instaliaâonBefore you begin, survey your garage area to see whether any of the conditions beiow apply to your instailatio
For professional installationCall 24 hours a day, 7 days a week1-800-865-6500For the repair or replacement parts you needCall 7 am - 7 pm, 7 days a we
ONE-PIECE Door Insfs^lattonBefore you begin, survey your garage area to see whether any of the conditions below apply to your installation.One-Piece D
Carton InventoryYour garage door opener is packaged in two cartons which contain aii parts iilustrated beiow. If anything is missing, carefully check
Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation procedures.Install
Assembly Section: Pages 8-11To avoid installation difficulties, do not run the garage door opener until instructed to do so.Assembly Step 1Assemble th
Assembly Step 2Instai! the Trolley on the T-raUTrolley• As a temporary stop, insert a screwdriver into the hole in the front end of the T-rail.• Slide
Kommentare zu diesen Handbüchern