Craftsman 247.775890 Bedienungsanleitung

Owner’s Manual10 Horse PowerCHIPPER-SHREDDERModel No.247.775890CAUTION: Before using this product, read this manual and follow all Safety Ru

AWARNING: Do not fill closer than 1/2inch from the top of the fuel tank to prevent spills and to allow for fuel expansion. If gasoline is accidently s

dkhopper assembly when it is in the raised or lowered position. See Figure 13. b. Bulky material, such as stalks or heavy branches, up to 3” in diamet

MAINTENANCEGeneral Recommendations• Always observe safety rules when performing any maintenance.• The warranty on this chipper shredder does not cov

the oi! must be to FULL mark on dipstick.• Change engine oil every 50 hours of operation under normal operating conditions. Change oil every 25 hours

Ahead, top of piston and around valves. Use a soft brush to remove the deposits.Reassemble gasket and cylinder head. Turn screws down finger-tight. To

SERVICE & ADJUSTMENTSRemoving Flail ScreenIf the discharge area becomes clogged, remove theflail screen and clean area as follows.• Stop engine,

Weld BoltFigure 20• Remove the six hex lock nuts and lock washers from the housing weld bolts using a 1 /2” wrench. Separate the chipper-shredder int

Check idle speed and re-adjust to 1750 rpm, if necessary.Engine should accelerate smoothly. If it does not, adjust idle mixture valve counter-clockwis

STORAGEPrepare your chipper-shredder for storage at the end of the seeison or if the unit will not be used for 30 daysor more.AWARNING: Never store ma

TROUBLE-SHOOTINGProblemPossible CauseCorrective ActionEngine fails to start1. Fuel tank empty, or stale fuel2. Spark plug wire disconnected3. Fault

TABLE OF CONTENTSContentPageContent PageWarranty Information2Service & Adjustment15Safe Operation Practices3Off-Season Storage18Assembiy5Trouble-S

PARTS LISTCRAFTSMAN 10 H.P. CHIPPER SHREDDER MODEL 247.77589020

CRAFTSMAN 10 H.P. CHIPPER SHREDDER MODEL 247.775890KeyNo.Part No.DescriptionKeyNo.Part No.Description_770-0819AOwner’s Manual45747-1124Flap Control Ro

CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-El FOR CHIPPER SHREDDERMODEL NO. 247.775890KeyNo. Part No.Description1495631Cylinder Assembly2495657Bus

CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-El FOR CHIPPER SHREDDERMODEL NO. 247.775890KeyNo.Part No.Description12*271701Gasket-Crankcase (.015&quo

CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-El FOR CHIPPER SHREDDERMODEL NO. 247.775890KeyNo.Part No.Description50214170 Manifold-Intake51 0*272707

CRAFTSMAN 10 H.P. ENGINE MODEL NO. 19G432-1182-E1 FOR CHIPPER SHREDDERMODEL NO. 247.775890KeyNo.Part No.Description116 *270920Seal-O-Ring209263212 Spr

215 305 24^CRAFTSMAN 10 Н.Р. ENGINE MODEL NO. 19G432-1182-El FOR CHIPPER SHREDDERMODEL NO. 247.775890KeyNo.Part No.Description23298260 Rywheel242226

For the repair or replacement parts you need delivered directly to your homeCall 7 am - 7 pm, 7 days a week1 -800-366-PART(1-800-366-7278)For in-home

SAFE OPERATION PRACTICESAThis symbol points out important safety instructions which, if not followed, could endanger the personal safety and/or prope

shut off. Never place any part of the body in the impeller area until you are sure the impeller has stopped rotating.Muffler and engine become hot and

ASSEMBLYLeaf Bag* The hoppar is packsd in the top insert In your chipper'Shrertder carton.Chip BagFigure 1Spark Plug WireFigure 2IMPORTANT: This

Figure 3• Place second spacer over hex bolt inside the other part of the hinge as shown in the inset. Secure tightly with hex lock nut.• Secure both

ARaise the hopper till it clicks into position. Unscrew the shoulder bolt from the stop washer on the inlet guide. See Figure 6.Align the loose end of

OPERATIONRead this owner's manual and safety rules before operating your chipper-shredder. Compare Figure 9 with your chipper-shredder to familia

Lowering Hopper AssemblyIn order to rake leaves into the hopper, you will needto lower the hopper.• To lower the hopper assembly, use one hand to gra