Owner’sManualModel No. 139.53662SRT 139.5367SSRTFor Residential Use OnlyCaution:Read and follow all safety rules and operating instructions before fir
Assembly Step 4install the Chain/Cable & Attach the Sprocket CoverDispensing CartonSerious Infury can resuit If fingers become entangled in
Assembly Step 5Tighten the Chain & Cable* Spin the inner ntft and lock washer down the threaded shaft, away from the troiley.* To tighten the chai
Installation Section: Pages 12 - 27Installation Step 1Determine HeBder Bracket LocBtion Installation procedures vary according to garage door types. F
Read the Safety instructions on page 12. They also apply to doors without tracks.' Close the door and mark the inside verticaJ centeriine of your
Installation Step 2Install the Header BracketYou can attach the header bracket either to the wall above the garage door, or to the ceiling. Follow the
Installation Step 3Attach the T-rail to the Header BracketHsacfer Wal• Position the opener on the garage floor below the header bracket Use packing ma
Installation Step 4Position the OpenerFollow Instructions which apply to your door type as illustrated.To prevent damage to steel, aluminum
Installation Step 5Häng the OpenerThe opener coutd fait and Injure someone If ft is not properly secured. Fasten the opener securely to
Installation Step 6Instai! the Premium Control ConsoleLocate the door control within sight of the door at a minimum height of 5 feet where small child
6. Attach tie User Safety Instruction iabei to the wall near the door control, and the Maintenance Instruction label in a prominent location on the i
ContentsA review of safety alert symbols...Youll need tools...Safety information reqardinq qaraqa
Instaiiation Step 9Electrical RequirementsTq reduce the risk of electric shock, your garage door opener has a grounding type plug with a third groundi
The Safety Reversing systemInformation you'll need before you begin the Installation of the safety reversing sensor.The safety reversing sensor m
installation Step 10Instai! the Safety Reversing SensorRgures 2 and 3 show assembly of brackets and 'C* wrap based on the recommended installatio
» Center each sensor unit in a 'C* wrap with tenses pointing toward each other across the door (see Hgure 6).• Secure sensors with the hardw
Installation Step 11Fasten Door BracketFoilow Instructions which apply to your door type as illustrated below or on page 25.I lUINIiTo prevent
" ...P!ease read and comply with the warnings and reinforcement instructions on page 24. They apply to one-piece doors also.• Center the
Installation Step 12 Connect Door Arm to Trolley Follow Instructions which apply to your door type as Illustrated below and on page 27,Make sure garag
Assemble the Door Arm:• fasten the straight and curved door arm sections together to the longest possible length, with a 2 or 3 hole overlap.• With th
Adjustment Section: Pages 28 - 30Adjustment Step 1Adjust the UP and DOWN LimitsDo not make any limit adjustments until the safety reversing sen
Adjustment Step 2Adjust the ForceForce adjtjsirnent contrais are located on the right Side рале1 of the opener. Force adjustment settings regulate the
You'll Need ToolsDuring assembiy, instaliation and adjustment of the opener, instructions wili cail for hand ioois shnwrs below.An unbalanced g
Adjustment Step 3T&st The Safety Reversing Sensor* Press the remote control push button to open the door.* Place the opener carton in the path of
IMPORTANT SAFETY INSTRUCTIONSTo reduce the risk of severe injury or death to persons:1. READ AND FOLLOW ALL INSTRUCTIONS,2. Do not permit children ei
Operation of Your OpenerActivate the opener with any of the following:• The Remote Control; Hold push button down until the door starts to move,"
Receiver and Remote Control ProgrammingSE€URnT+Your garage door opener receiver and remote control have been pre-set at the factory. The door will ope
SituationHaving a Problem?Probable Cause and SolutionThe opener doesn't operate from either the Door Control or the remote control:1. Doe
Having a Problem? (continued)SituationProbable Cause & SolutionThe door opens but woni dose:1. if the opener lights blink, check the safety rever
Repair PartsRail Assembly PartsJjl^^yyNO.PARTNO.DESCRIPTION11A995Master link kit2 41A3489Compiete trolley assembly3 1B3117T-rail "Center section4
Repair Parts)pctner Assembly PartsKEYNO,PARTNO.DESCRIPTIONKEYNO.PARTNO.131D380Sprocket cover9108D4S-2241C4220AOear and sprocket assembly1030B363Comple
AccessiSears offers rr Sears model nilany useful accessories for your garage door opener. They are IHusirated below vi Ith jmbers and d
|nci0XAccess Doar/Outside Key Retease Accessory.Chain Tension...™...Electrical Safety Warnings..Garage DoorTesting for balance, bindi
Before you begin, survey your garaoe area to see whether any of the conditions fallow apply to your installation.^ Hofizofita] and vafii
For professional installation Call 24 hours a day, 7 days a week1 -800.865-6500For the repair or replacement parts you needCal! 7 am - 7 pm, 7 days a
i :,,CiQN E'PiH©Es00Qiilia§ta|№iilBe'fore you begin, survey your garage area to see whether any of the conditions below apply to your instal
Carton InventoryYour garage door opener is packaged in two cartons which contain aii parts illustiated below. If anything is missing, carefully check
Separate all hardware from the packages in the rail carton and the opener carton, as shown below, for the assembly and installation proc
Assembly Section: Pages 8-11To avoid installation difficulties, do not run the garage door opener until Instructed to do so.Assembly Step 1Assemble th
Assembly Step 3Fasten the T-rail to the Opener• Place the opener on packing material to protect the cover. For convenience, put a support under the ca
Kommentare zu diesen Handbüchern