Craftsman 137.218100 Betreibershandbuch

Operator's ManualCRFIFrXMFIN°3.0 HP (Max. Developed)10" Inch Blade5000 R.P.M.TABLE SAWModel No.137.218100137.248100 / with StandTABLE SAWCAU

RIP FENCE (FIG. E)1. Thread the fence handle (1) into the cam hole (2)until tight.2. Lift upward on the rip fence handle (t) so that theholding clamp

BLADEGUARDASSEMBLY(FIG.I,J, K)1.Setthebladetomaximumheightand the tilt tozero degrees on the bevel scale with the handwheels. Lock the blade lock knob

ADJUSTMENT INSTRUCTIONSTo avoid injury from an accidental start, make sure theswitch is in the OFF position and the plug is notconnected to the power

To avoid injury from an accidental start, make sure theswitch is in the OFF position and the plug is notconnected to the power source outlet.ADJUSTING

Additional blade adjustments (Fig. T)1. If the front and rear measurements are not the same,remove the combination square and loosen the fouradjusting

BASIC SAW OPERATIONSRAISE THE BLADE (FIG. U)To raise or lower the blade, turn the blade elevationhandwheel (1) to the desired blade height, and thenti

CUTTINGOPERATIONSTherearetwobasictypesofcuts:rippingandcrosscutting.Rippingiscuttingalongthelengthandthegrainoftheworkpiece.Crosscuttingiscuttingeithe

BEVELRIPPINGThiscutisthesameasrippedexcept the blade bevelangle is set to an angle other than "0".Cut only with the workpiece and the fence

COMPOUNDMITER CROSSCUTTING (FIG. BB)This sawing operation is combining a miter angle with abevel angle.1. Set the miter gauge (3) to the desired angle

MAINTAINING YOUR TABLE SAWGENERAL MAINTENANCEFig. FFFor your own safety, turn the switch OFF and removethe switch key. Remove the plug from the power

SECTION PAGEWarranty ... 2Product Specifications ... 2Power Tool Safety ...

Toavoidinjuryfromanaccidentalstart,turntheswitchOFFandalwaysremovetheplugfromthepowersourcebeforemakinganyadjustments.• ConsultyourlocalSearsServiceCe

boCut off here topush 1/4" wood.Cut off here to1/2" woo&mi1/2" Squares.iriNotch to helpt prevent handfrom slipping.J ittiJiiPUSHSTI

10" TABLE SAW PARTS LISTWARNING IMODEL NO. 137.218100/137.248100When servicing use only CRAFTSMAN replacement parts. Use of any other parts many

J21eMJ \\\Q_B\\)//W-_. r-m0C3mr-Z0(.3"-4ko=_oo_=_=_"-4ko4_O0

10" TABLE SAW PARTS LIST MODEL NO. 137.218100/137.248100Schematic BI.D. NO. DESCRIPTION SIZE QTY I.D. NO. DESCRIPTION SIZE QTY09JK WRENCH HEX 1 0

/o_OBPA-_. t-o mO3O_3mr-ZO(*3"-4ko=_oo_=_=_"-4ko4_00(D(D

10" TABLE SAWPart list for MOTORMODEL NO. 137.218100/137.248100I.D. NO, DESCRIPTION SIZE QTY1502 FIELD ASS'Y 11503 ARBOR SHAFT 10HV5 BALL BE

:)l_oOq_Ao;0_g ggr-m0mr-Z0..Mi,oco,ramco

Your HomeFor repair-in your home-of all major brand appliances,lawn and garden equipment, or heating and cooling systems,no matter who made it, no mat

Before using your table saw, it is critical that you read and understand these safety rules.Failure to follow these rules could result in serious inju

.ALWAYS USE SAW BLADE GUARD, splitter and 12.anti-kickback pawls for every operation for which theycan be used, including through-sawing Through-sawin

POWER SUPPLY REQUIREMENTSTo avoid electrical hazards, fire hazards or damage tothe table saw, use proper circuit protection. Alwaysuse a separate elec

RECOMMENDED ACCESSORIESUNPACKING AND CHECKING CONTENTSVisit your Sears Hardware Department or see theCraftsman Power and Hand Tools Catalog to purchas

UNPACKING "tOUR TABLE SAW:!_LANCGH|M

Rip FenceBlade GuardTable InsertMiter GaugeTableSideTableExtensionExtensionhandlesBlade bevellock knobwith keyOverload resetswitchMounting holesBlade

SAW MOUNTED TO WORK SURFACE (FIG. A)1. If the leg set will not be used, the saw must beproperly secured to a sturdy workbench using thefour mounting h