Craftsman 208cc Bedienungshandbuch PDF herunterladen (Seite 17)

OPERATION

2. Move throttle control to FAST (rabbit) position.

3. Move choke to the CHOKE position (cold engine start). If engine is

warm, place choke in RUN position.

4. Push primer three (3) times, making sure to cover vent hole in primer bulb

when pushing. If engine is warm, push primer only once. Always cover vent

hole when pushing. Cool weather may require priming to be repeated.

5. Push starter button to start engine. Once the engine starts, immediately

release starter button. Electric starter is equipped with thermal overload

protection; system will temporarily shut-down to allow starter to cool if

electric starter becomes overloaded.

6. As the engine warms, slowly rotate the choke control to RUN position. If the

engine falters, restart engine and run with choke at half-choke position for a

short period of time, and then slowly rotate the choke into RUN position.

7. After engine is running, disconnect extension cord from electric starter.

When disconnecting, always unplug the end at the wall outlet before

unplugging the opposite end from the engine.

Recoil Starter

CAUTION

Do not pull the starter handle while the engine running.

1. Move throttle control to FAST (rabbit) position.

2. Move choke to the CHOKE position (cold engine start). If engine is

warm, place choke in RUN position.

3. Push primer three (3) times, making sure to cover vent hole when pushing.

If engine is warm, push primer only once. Always cover vent hole when

pushing. Cool weather may require priming to be repeated.

4. Pull gently on the starter handle until it begins to resist, then pull quickly

and forcefully to overcome the compression. Do not release the handle and

allow it to snap back. Return rope SLOWLY to original position. If required,

repeat this step.

5. As the engine warms, slowly rotate the choke control to RUN position. If the

engine falters, restart engine and run with choke at half-choke position for a

short period of time, and then slowly rotate the choke into RUN position.

WARNING

To avoid unsupervised engine operation, never leave the machine

unattended with the engine running. Turn the engine off after use and

remove key.

Stopping The Engine

After you have finished snow-throwing, run engine for a few minutes before

stopping to help dry off any moisture on the engine.

1. Move throttle control to OFF position.

2. Remove the key. Removing the key will reduce the possibility of

unauthorized starting of the engine while equipment is not in use. Keep the

key in a safe place. The engine cannot start without the key.

3. Wipe any moisture away from the controls on the engine.

To Engage Drive

1. With the throttle control in the Fast (rabbit) position, move shift lever

into one of the six forward (F) positions or two reverse (R) positions. Select a

speed appropriate for the snow conditions and a pace you’re comfortable

with.

NOTE: When selecting a Drive Speed, use the slower speeds until you are

comfortable and familiar with the operation of the snow thrower.

2. Squeeze the drive control against the handle and the snow thrower will

move. Release it and drive motion will stop.

NOTE: NEVER reposition the shift lever (change speeds or direction of travel)

without first releasing the drive control and bringing the snow thrower to a

complete stop. Doing so will result in premature wear to the snow thrower’s drive

system.

To Engage Auger

1. To engage the auger and start throwing snow, squeeze the auger control

against the left handle. Release to stop the auger.

Replacing Shear Pins

Each auger blade is secured to the spiral shaft with a shear pin and bow-tie clip. If

an auger blade strikes a foreign object or ice jam, the pin will shear off to prevent

damage to the blade. If an auger blade does not turn, check to see if its pin has

sheared off. See Figure 16.

CAUTION

NEVER replace the auger shear pins with anything other than Sears SKU#

88389/OEM Part No. 738-04124A replacement shear pins. Any damage to

the auger gearbox or other components as a result of failing to do so will

NOT be covered by your snow thrower’s warranty.

WARNING

Always turn off the snow thrower’s engine and remove the key prior to

replacing shear pins.

Figure 16

1 2 ... 12 13 14 15 16 17 18 19 20 21 22 ... 59 60

Kommentare zu diesen Handbüchern

Keine Kommentare

Craftsman 208cc Bedienungshandbuch Seite 17

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Schneewerfer Craftsman 208cc