Craftsman 113 Bedienungshandbuch PDF herunterladen (Seite 2)

FULL ONE YEAR WARRANTY ON CRAFTSMAN TABLE SAW

If withirl-one year from the date of purchase, this Craftsman Table Saw fails due to a defect in material or

workmanship, Sears will repair it, free of charge. This warranty applies only while this product is in use in the United

States.

WARRANTY SERVICE IS AVAILABLE BY SIMPLY CONTACTING THE NEAREST SEARS SERVICE

CENTER/DEPARTMENTTHROUGHOUT THE UNITED STATES•

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

SEARS, ROEBUCK AND CO., Dept. 698/781A. SearsTower, Chicago, IL 60684

GENERAL SAFETY INSTRUCTIONS

FOR POWER TOOLS

1. KNOW YOUR POWER TOOL

Read and understand the owner's manual and labels

affixed to the tool Learn its application and

limitations as well as the specific potential hazards

peculiar to this tool.

2. GROUND ALL TOOLS

This tool is equipped with an approveo 3*conductor

cord and a 3-prong grounding type plug to fit the

proper grounding tvpe receptacle. The green conductor

in the cord is the grounding wire. Never connect the

green wire to a live terminal.

3. KEEP GUARDS IN PLACE

in working order, and in proper adjustment and

alignment.

4. REMOVE ADJUSTING KEYS

AND WRENCHES

Form habit of checking to see that keys and adjusting

wrenches are removed from tool before turning it on.

5. KEEP WORK AREA CLEAN

Cluttered areas and benches invite accidents, Floor

must not be slippery due to wax or sawdust.

6. AVOID DANGEROUS ENVIRONMENT

Don't use power tools in damp or wet locations or

expose them to rain. Keep work area well lighted.

Provide adequate surrounding work space.

7. KEEP CHILDREN AWAY

All visitors should be kept a safe distance from work

area,

8. MAKE WORKSHOP KID-PROOF

-- with padlocks, master switches, or by removing

starter keys.

9. DON'T FORCE TOOL

It will do the job better and safer at the rate for which

it web dc_igncd.

10. USE RIGHT TOOL

Don't force tool or attachment to do a job it was not

designed for.

11. WEAR PROPER APPAREL

Do not wear loose clothing, gloves, neckties or jewelry

(rings, wrist watches) to get caught in moving parts.

Nonslip footwear is recommended. Wear protective

hair covering to contain long hair. Roll long sleeves

above the elbow.

12. USE SAFETY GOGGLES (Head Protection)

Wear Safety goggles (must comply with ANSI Z87.1)

at all times. Everyday eyeglasses only have impact

resistant lenses, they are NOT safety glasses. Also, use

face or dust mask if cutting operation is dusty, and ear

protectors (plugs or muffs) during extended periods of

opera_ion

13. SECURE WORK

Use clamps or a vise to hold work when practical. It's

safer than using your hand, frees both hands to operate

tool.

14. DON'T OVERREACH

Keep proper footing and balance at all times.

15. MAINTAIN TOOLS WITH CARE

Keep tools sharp and clean for best and safest

performance, Follow instructions for lubricating and

changing accessories.

DISCONNECT TOOLS

before servicing; when changing accessories such as

blades, bits, cutters, etc.

17. AVOID ACCIDENTAL STARTING

Make sure switch is in "OFF" position before plugging

in.

18. USE RECOMMENDED ACCESSORIES

Consult the owner's manual for recommended

accessories. Follow the instructions that accompany

the accessories. The use of improper accessories may

cause hazards.

19. NEVER STAND ON TOOL

Serious injury could occur if the tool is tipped or if the

cutting tool is accidentally contacted.

Do not store materials above or near the tool such that

it is necessary to stand on the tool to reach them.

20. CHECK DAMAGED PARTS

Before further use of the tool, a guard or other part that

is damaged should be carefully checked to ensure that it

will operate properly and perform its intended function.

Check for alignment of moving parts, binding of moving

parts, breakage of parts, mounting, and any other

conditions that may 'affect its operation. A guard or

other part that is damaged should be properly repaired

or replaced.

21. DIRECTION OF FEED

Feed work into a blade or cutter against the direction

of rotation of the blade or cutter only.

22. NEVER LEAVE TOOL RUNNING

UNATTENDED

Turn power off. Don't leave tool until it comes to a

complete stop.

• 16.

1 2 3 4 5 6 7 ... 47 48

Kommentare zu diesen Handbüchern

Keine Kommentare

Craftsman 113 Bedienungshandbuch Seite 2

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Bohrmaschinen Craftsman 113